Washer Repair
Washer Repair Huntsville AL
Front-loader or top-loader, washers that won’t drain, won’t spin, leak, walk across the floor, or smell like mildew. We check the pump, valves, gaskets, switches, and belts.
Common Problems
Washer Repair Services
Four problems come up again and again. Each one points to a short list of likely causes.
🔄 Washer Not Spinning
The washer fills and agitates, but your clothes come out soaking wet.
Common causes: a lid switch or door lock that isn’t registering, a worn drive belt, a bad motor coupling on a top-loader, a failing motor, or a control board fault. An unbalanced or overloaded drum can also stop the spin.
Check first: redistribute the load, don’t stuff the drum, and press the lid or door firmly closed. If it still won’t spin, call us.
💧 Washer Not Draining
Water sits in the tub after the cycle ends.
Common causes: a clogged drain pump filter, a kinked or blocked drain hose, a failed drain pump, or a clog in the household standpipe. If the clog is in your house drain, we’ll tell you, since that’s a plumbing fix.
Check first: many front-loaders have a small drain filter behind a panel at the bottom front. Set towels and a shallow pan down, then open it slowly. Water will come out. On some machines, a drain error code shows up, such as F21 on certain Whirlpool washers, OE on many LG washers, and 5E on many Samsung washers.
⏻ Washer Not Starting
Two cases: the display is dark, or the lights come on but the cycle won’t begin.
Check first: the outlet, the breaker, and whether the lid or door is fully latched. Look for a child lock, a cycle lock, or a delay start on the display.
Common causes: a failed lid switch or door latch, a control board fault, or a blown thermal fuse on some models.
🚿 Washer Leaking
Where the water appears points to the cause.
Front door: a torn or dirty door boot gasket on a front-loader.
Back of the machine: a worn supply hose or a failed inlet valve.
Underneath: a drain pump, a loose hose clamp, or a tub seal.
Suds and overflow: too much detergent. Use HE detergent in the amount on the label.
Check first: shut off both supply valves and unplug the washer. Wet floors can ruin subflooring, so don’t wait.
More Fixes
Washer Problems We Fix
Washer Not Filling With Water
Check that both supply valves are open and the hoses aren’t kinked. Clogged inlet screens, a failed water inlet valve, a bad water-level sensor, or a door lock fault can all stop the fill. Turn off the water, remove a hose, and rinse the screen to test the simple fix first.
Washer Not Agitating
On a top-loader, the agitator may spin slowly, or not at all. Worn agitator dogs, a bad motor coupling, a slipping belt, or a failing transmission are the usual suspects. If the washer spins clothes but won’t agitate, say so when you call.
Washer Making Noise
A rumble or roar during spin: worn drum bearings.
Thumping: an unbalanced load or worn suspension rods.
Squealing: a belt, motor, or pump.
Rattling or clicking: coins, keys, or underwires caught in the pump or drum.
Check pockets and the drain filter first. A roaring bearing needs a pro.
Washer Shaking or Vibrating
If the washer walks across the floor, check these first: the feet aren’t level, the shipping bolts weren’t removed on a new front-loader, the load is too heavy or lopsided, or the shock absorbers are worn. Upstairs laundry rooms and older floors make it worse.
Brands
Washer Brands We Repair
[List only brands your technician actually services.] Brands from the same maker often share parts. Send us your model number and any error code or blinking light pattern.
Samsung Washer Repair
Common Samsung calls include vibration and balance problems, clogged drain pump filters, and door lock faults.
LG Washer Repair
Many LG washers use direct-drive motors. Calls we see include door lock errors, drain pump clogs, and control board faults.
Whirlpool Washer Repair
On Whirlpool top-loaders, we replace motor couplings and lid switches. On front-loaders, door boot gaskets and mildew problems are common. Whirlpool shares parts with Maytag, KitchenAid, and Amana.
Maytag Washer Repair
Maytag top-loaders bring us agitator, coupling, and lid switch problems, and many Maytag parts match Whirlpool parts.
Pricing
Washer Repair Cost
Not draining
Drain pump or filter clean
$100–$300
Not filling
Water inlet valve
$100–$250
Not spinning
Belt, coupling, or lid switch
$100–$300
Leaking at door
Door boot gasket
$150–$400
Door won’t lock
Door lock assembly
$100–$250
Loud spin noise
Bearings or tub seal
$250–$600
Why Us
Why Choose Our Washer Repair
Experienced Technicians
Connect with experienced washer repair professionals.
Price Before Work
Review the estimate before approving repairs.
Honest Advice
Know when repairing your washer may not be worth the cost.
Clear Scheduling
Convenient appointment scheduling with arrival updates.
Written Warranty
Ask about available parts and labor warranty coverage.
How It Works
Washer Repair Process
1
Book.
Call, text, or use the form. Tell us the brand and what it’s doing. A photo of the model sticker helps.
2
Diagnose.
We check the drain, the door lock or lid switch, the belt or coupling, the inlet, and any error codes.
3
Quote.
You get the price and your options before we start. [If the price changes, we call you before continuing.]
4
Repair.
[Many repairs finish in one visit when the part is on the truck.] If a part must be ordered, we tell you how long it will take.
5
Test.
We run a cycle, watch for leaks, and listen for noise before we leave.
[Book Washer Repair] or call [PHONE].
FAQs
Washer Repair FAQs
Need Help? Call Us
Call or text [PHONE] and describe the problem. We’ll tell you what to expect.